Disclaimer: What you do with this information is up to you. You are fully responsible for what you do with this info, and how you use it. HackMethod is not responsible for your actions. Please do not hack Wifi points that you are not allowed to.

NOTE: I do advise having a USB WiFi adapter, and an extra point would be to get a great one like the ALFA AWUS036NHR or AWUS051NH. Although any card would do as long as it supports monitor mode and packet injection.


When it comes to the world of WiFi hacking, the possibilities are only limited by your imagination. Skilled hackers can combine attacks together for increased efficiency, and can also judge on which attack is best to use given a particular situation. By the end of this guide you should have an overall idea on the types of attacks that you can use against any WiFi-enabled AP or router.

Getting Started

The tool that this guide will be using is Wifite.

Now I wont be including how to do it using any other tools, because this should work just fine. I’ll leave the exploration up to you.

To get started, install Wifite on your machine by following the installation instructions that are stated here.

Scanning for Wifi points

Simply run wifite.py -i <wlan interface here *NOT IN MONITOR MODE*> or if you didnt understand the previous command simply use wifite.py and it will begin scanning for nearby access points and their features (Encryption method and if WPS is enabled or not).

NOTE: I always recommend to spoof your mac address using the --mac flag to the program or macchanger. Its for your safety.

Here are the 3 types of targets you can find:

  • WEP protected routers
  • WPA/WPA2 protected routers
  • Open routers

Now within those categories, you can find a feature called WPS (Wi-Fi Protected Setup) enabled, which uses an 8 digit PIN to add devices to a WiFi network without having to input long passwords.

Attacking WEP protected WiFi points

WEP is an old and depreceated way of protecting WiFi passwords, so if you find one, you are in luck. WEP takes substantially less time. This is easily automated in Wifite, and it even uses multiple attacks against routers to get the password. You only need around ~10 to 120 minutes to crack WEP, maybe longer. I cant say much because I have never seen any WEP protected routers were I live and never had the time to set one up and try myself.

Here is how the attack should look (picture taken from Wifite Github wiki):

Wifite running against WEP protected WiFi points

Wifite running against WEP protected WiFi points

Attacking WPA/WPA2 protected WiFi points

When it comes to WPA, we need to grab the handshake by deauthing clients who are connected to the router and sniffing the handshake as it goes. This is automated in Wifite, and it handles everything. Note: You may grab the handshake in a small amount of time, but cracking the hash itself will take a pure brute-force attack or a wordlist, which takes alot of time. Only use this method if you have a really powerful GPU/CPU or if all other options have failed.

Attacking WPS enabled WiFi points

Now comes the fun part, WPS cracking. There are 2 attacks you can do on WPS enabled routers, a WPS PIN bruteforce and a WPSPixie attack. The WPS PIN attack works online, as in all PIN guesses are actually sent to the router, while the WPSPixie attack works offline and without flooding the router with WPS PIN attempts.

Now the obvious disadvantage about the WPS PIN attack is that some routers have on-board anti-bruteforce mechanisms and will stop accepting your attempts after a few attempts. I only go this route if the WPSPixie attack fails and there is no anti-bruteforce mechanism (Wifite will tell you if detects one).

The WPSPixie attack is one of the best attacks on Wifi points I have ever seen. In most cases, you can get the WiFi password in minutes or even a few seconds. Be aware that it may take up to 30 minutes in some cases, although I have never personally seen it go beyond 10 or so minutes. NOTE: The WPSPixie attack may not work on some routers, and you will have to choose a different route. (Wifite will also notify you if the WPSPixie attack will not work.

NOTE: Sometimes you will see that Wifite gets stuck at Waiting for beacon from "xx:xx:xx:xx". If it gets stuck for a while at this point, press CTRL+C and move on to a different target.

Wifite hacking WPS enabled points using WPS PIN Bruteforce


So thats pretty much it when it comes to hacking WiFi using Wifite. There are other ways of doing this, such as using the aircrack-ng suite of tools and/or using dedicated WPS hacking tools such as reaver. Additionally, this guide is only but a small slice of the world of wireless hacking, so be sure to stay tuned for more wireless hacking tutorials soon!

You were not leaving your cart just like that, right?

Enter your details below to save your shopping cart for later. And, who knows, maybe we will even send you a sweet discount code :)